PARTS LIST
ONE WAY-CORD LEFT
ONE WAY-CORD LEFT
ONE WAY-CORD RIGHT
ONE WAY-CORD RIGHT
1. Pulley Housing
2. End Bracket
3. Inside Section of Rod
4. Outside Section of Rod
5. Center Support
6. Cord
7. Slide
8. Master Carrier
3
ATTACH ROD INTO CENTER SUPPORT BY TURNING
SILVER COLOR BRACKET WHEEL.
4
SPECIAL INSTRUCTION
2. CEILING INSTALLATION. If rod is to be installed to ceiling, attach pulley housings
(without brackets) and stirrup portion of center support directly to ceiling.
WARNING
TO AVOID POSSIBLE STRANGULATION, KEEP CORDS OUT
OF REACH OF CHILDREN. USE THESE DEVICES:
1. CLAMP OR CLOTHES PIN
2. CLEAT
3. TIE THE CORD TO ITSELF
4. TIE-DOWN DEVICE.
!
1. TENSION PULLEY OPTION: can be
mounted to the wall or oor. After securing
Tension Pulley to desired location, loop
cord onto pulley wheel. Grasp cord joining
knot behind Master Carrier and pull out
enough cord to take up slack between the
rod and the cord tension pulley. (Fig. 2)
Retie knot as close to the Master Carrier as
possible then cut off excess cord beyond
knot. Rotate pulley head until cords are in
proper alignment and release into pulley
base.
INSTALLATION INSTRUCTIONS FOR ONE-WAY / SINGLE TRAVERSE ROD (Drop In)
MOUNTING INSTRUCTIONS:
Wall mount option- Mount the one
end bracket and one support to the
wall at desired location. No center
support is needed for installations
less than 50” long. Ceiling mount
option- If rod is to be installed to the
ceiling, attach pulley housing (without
brackets) and stirrup portion of center
support directly to the ceiling.
1
FOR RODS FULLY EXTENDED TO
50” OR MORE, INSTALL CENTER
SUPPORT.
2
REMOVAL OF UNUSED CARRIER SLIDES
5
HANG DRAPERIES
7
1
2
3
Push up the end gate to remove carrier slides
Center Support
Center SupportEnd brackets End brackets
5
5
6
6
2
2
7
7
1
1
8
8
3
3
4
4
Fig. 1
CHILD SAFETY CORD GUIDE: RODS WILL NOT WORK PROPERLY WITHOUT GUIDE INSTALLED
Guide is pre-attached to the cord. Mount the guide to the wall at the desired height using the included screw. Tighten the screw
until the cord slides through the device freely. (See Fig. 1) Remove excess slack on the cord by grasping and pulling down on the
knot that is on the back side of the master carrier. Pull the knot out until the cord is taught in the guide. Tie a new knot into the cord
as close as possible to the master carrier and cut off the excess cord. (See Fig. 2)
CHILD SAFETY CORD GUIDE REMOVAL: Pry open the three clips on the back of the device. (See Fig.3) Split the guide open
and remove the cord guide.
6
Fig. 1
Fig. 3
Fig. 2
Overlap
Master Carrier
Joining
Knot
Knots
cut
INSTALL ROD INTO END BRACKET: drop end
of rod into the u-shaped clip of the end bracket. To
remove rod from bracket simply lift the rod out of
the u-shaped clip.
End bracket
Spring clip
Pulley housing
Stirrup
ATTACH SUPPORT TO THE ROD
The support arm goes over the top of the rod with
the silver cam lock toward the oor. The rod ts
into the arm hook and locks in by turning the cam
lock with a at bladed screwdriver. Do not turn
the Philips screw.
TURN
LOCK!
Projection may be adjusted, if needed, by loosening adjusting screws.
Center Support
PROJECTION
Adjusting Screws
(1 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern